User Tools

Site Tools


troubleshooting_ingenico_6550_6780

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
troubleshooting_ingenico_6550_6780 [2010/09/29 07:54 (14 years ago)] swindtroubleshooting_ingenico_6550_6780 [2021/05/11 22:31 (3 years ago)] (current) medano
Line 1: Line 1:
  
-[[http://wws5.com/|{{http://wws5.com/images/topxxxgif-ani.gif  |Windward Software}}]]+
  
  
Line 10: Line 10:
 http://wiki.wws5.com/doku.php?id=pos_devices_-_signature_capture&s=6550 http://wiki.wws5.com/doku.php?id=pos_devices_-_signature_capture&s=6550
  
-To setup the , you need to download the following file from Windward's FTP site+To set up the , you need to download the following file from Windward's FTP site
  
 ftp://ftp.windward-ca.com/pub/special/ingenico_s5.zip ftp://ftp.windward-ca.com/pub/special/ingenico_s5.zip
Line 18: Line 18:
 error: pinpad opos_not claimed 103 error: pinpad opos_not claimed 103
  
-This error occurred when we tried to load the forms during the set up in the setup wizard. Customer had moved computer while it was up and running and the power supply was inadvertently unplugged from the serial port adapter, which appeared to have blown the serial port. So we were not able to connect the device serially to the computer. We then attempted to connect through TCPIP. After following the instructions on "Using Under Terminal Services" in the Ingenico6xxx.chm file (Windows help file located in the installation folder c:\ingenico_s5), we were still unable to get the pinpad to work. We continued to get the "pinpad opos_not claimed 103" error every time we tried to send the forms to it.+This error occurred when we tried to load the forms during the set up in the setup wizard. The customer had moved the computer while it was up and running and the power supply was inadvertently unplugged from the serial port adapter, which appeared to have blown the serial port. So we were not able to connect the device serially to the computer. We then attempted to connect through TCPIP. After following the instructions on "Using Under Terminal Services" in the Ingenico6xxx.chm file (Windows help file located in the installation folder c:\ingenico_s5), we were still unable to get the pinpad to work. We continued to get the "pinpad opos_not claimed 103" error every time we tried to send the forms to it.
  
  
 ====== Solving The Issue ====== ====== Solving The Issue ======
  
-The first thing to check is that the Local IP Port in the device is set correctly. It should be set to 8001. If you set up more than one of these pin pads at a location each pinpad should have a different number, so pinpad 2 could be 8002, pinpad 3 could be 8003 etc. Also be aware that within the Setup Wizard, in the pinpad setup, the Port Number must match that number you set in the pinpad. +The first thing to check is that the Local IP Port in the device is set correctly. It should be set to 8001. If you set up more than one of these pin pads at a location each pinpad should have a different number, so pinpad 2 could be 8002, pinpad 3 could be 8003etc. Also be aware that within the Setup Wizard, in the pinpad setup, the Port Number must match that number you set in the pinpad. 
-Also if the pinpad has been previously set up as a serial or USB connection, you may need to delete the SignatureCapture key in the registry. To do this, go to the start button, and select run, then type regedit, and hit enter. now browse to: HKEY_LOCAL_MACHINE\SOFTWARE\OLEforRetail\ServiceOPOS. Click on SignatureCapture. then right click on it and select Delete from the drop down. Now reinstall the Ingenico software, and make the necessary changes for the connection type. This should allow you to update the forms from the setup wizard now. +Also if the pinpad has been previously set up as a serial or USB connection, you may need to delete the SignatureCapture key in the registry. To do this, go to the start button, and select run, then type regedit, and hit enter. now browse to: HKEY_LOCAL_MACHINE\SOFTWARE\OLEforRetail\ServiceOPOS. Click on SignatureCapture. then right-click on it and select Delete from the drop-down. Now reinstall the Ingenico software, and make the necessary changes for the connection type. This should allow you to update the forms from the setup wizard now.  
 + 
 + 
 +== Steve Wind Sept 29, 2010 == 
 + 
 + 
  
  
-== Steve Wind Sept 29 2010 == 
  
 ====== ======
-[[http://mywindward.wws5.com|{{  http://wws5.com/support/images/cust_support_banner_bottom.jpg  |myWindward+[[http://mywindward.wws5.com|{{  http://wws5.com/support/images/cust_support_banner_bottom.jpg  |myWindward}}]]
troubleshooting_ingenico_6550_6780.1285772080.txt.gz · Last modified: 2010/09/29 07:54 (14 years ago) by swind