User Tools

Site Tools


faq:ibc_equipment_setup

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
faq:ibc_equipment_setup [2017/02/01 13:59 (7 years ago)] swindfaq:ibc_equipment_setup [2019/11/07 09:02 (4 years ago)] – [POS Tablet ION-TAB8-Z4UG] craig
Line 1: Line 1:
-{{:windward_supported_hardware_list:posx-omni-config.png?linkonly|}}====== IBC Equipment Setup for Windward Software ======+{{:windward_supported_hardware_list:posx-omni-config.png?linkonly|}} 
 +====== IBC Equipment Setup for Windward Software ======
 This is an overview of how to configure POSX point of sale equipment provided by International Bar Code (IBC). This is an overview of how to configure POSX point of sale equipment provided by International Bar Code (IBC).
  
Line 9: Line 10:
   * 16" Cash Drawer (POSX ION-C16A-1B)   * 16" Cash Drawer (POSX ION-C16A-1B)
   * Barcode Scanner (ie:XI3000U or POS-X EVO 2D scanner)   * Barcode Scanner (ie:XI3000U or POS-X EVO 2D scanner)
 +
 +
  
 <note>Power on switch is located on right bottom of screen right near the power plug in.</note> <note>Power on switch is located on right bottom of screen right near the power plug in.</note>
Line 28: Line 31:
 \\ \\
  
-===== Poll Display 8200USB ===== +===== Pole Display 8200USB ===== 
-The Poll display is USB but will emulate as a serial device once the drivers are installed. First, download and install the 8200-USB driver which will allow you to configure the port settings to be used for the device. Once installed, download and extract the 8200-2200.zip file and run the VFD_Setup.exe file. This will allow you to set the Poll Display in a number of different configuration settings. We recommend setting the Poll display to be in DSP-800 mode. The user can load the 8200-DSP-800.vfd file which will pre-set the settings required for the DSP-800:+The Pole display is USB but will emulate as a serial device once the drivers are installed. First, download and install the 8200-USB driver which will allow you to configure the port settings to be used for the device. Once installed, download and extract the 8200-2200.zip file and run the VFD_Setup.exe file. This will allow you to set the Pole Display in a number of different configuration settings. We recommend setting the Pole display to be in DSP-800 mode. The user can load the 8200-DSP-800.vfd file which will pre-set the settings required for the DSP-800:
    
  
-Once the settings have been downloaded to the device, the WindwardPOS device manager can be set to use the DSP-800 as the Poll display.+Once the settings have been downloaded to the device, the WindwardPOS device manager can be set to use the DSP-800 as the Pole display.
  
 \\ \\
Line 166: Line 169:
 \\ \\
  
 +===== POS Tablet ION-TAB8-Z4UG ===== 
 +  
 +Setup the Zebra embedded Scanner as instructed here. [[https://www.zebra.com/us/en/support-downloads/knowledge-articles/evm/emulating-a-com-serial-port-over-usb-using-cdc-driver.html|USB-COM]].  There is no article on reverting so don't do this willy-nilly.\\ 
 +This will create a Virtual USB-Serial Port in the device manager.\\ 
 +Select this serial port in the POS Device Manger.\\
 ===== HP ElitePad with Retail Jacket (Beta - not currently supported) ===== ===== HP ElitePad with Retail Jacket (Beta - not currently supported) =====
   * This tablet is a W8 tablet with MSR and barcode scanner.   * This tablet is a W8 tablet with MSR and barcode scanner.
faq/ibc_equipment_setup.txt · Last modified: 2020/06/02 09:57 (4 years ago) by kevin