User Tools

Site Tools


datalogic_quickscan_2d

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
datalogic_quickscan_2d [2016/08/26 11:20 (8 years ago)] swinddatalogic_quickscan_2d [2018/09/07 09:30 (6 years ago)] swind
Line 1: Line 1:
-====== Datalogic QuickScan (2D Models) ======+{{ :barcodescan:820055914_tom.pdf |}}====== Datalogic QuickScan (2D Models) ======
  
  
Line 12: Line 12:
 ====== Programming The Datalogic QuickScan 2D Barcode Scanner ====== ====== Programming The Datalogic QuickScan 2D Barcode Scanner ======
  
 +===== This setup would be the same for System Five on Cloud configuration.=====
  
 ===== Models : Datalogic QuickScan QD24XX – QBT24XX – QM24XX ===== ===== Models : Datalogic QuickScan QD24XX – QBT24XX – QM24XX =====
Line 36: Line 37:
 {{:barcodescan:barcode:capture5.jpg|}}  {{:barcodescan:barcode:capture5.jpg|}} 
  
-Manual can be downloaded from http://www.datalogic.com/tools/download.aspx?iddwnfile=10057&path=%2fupload%2fmarketlit%2fmanuals%2ftouchtd1100%2f820055914.pdf&name=820055914+Manual can be downloaded from  
 + 
 +{{ :barcodescan:barcodescan:qbt2400:820055914.pdf |}}
  
  
 Installed the USB to Serial driver Installed the USB to Serial driver
-http://www.datalogic.com/tools/download.aspx?iddwnfile=14128&path=%2fupload%2fmarketlit%2fsoftware%2futilities%2fdriver+usb%2f4.5.0%2fUSB-COM-x64.zip&name=USB-COM-x64+ 
 +{{ :barcodescan:barcodescan:qbt2400:dr9100399.zip |}} 
 Windows automatically picked up the scanner and installed the drivers. Windows automatically picked up the scanner and installed the drivers.
  
Line 54: Line 59:
  
 Now you will need to open the POS Device Manager as administrator and set the port to the one in the Windows Device Manager (Shown in picture above). Now you will need to open the POS Device Manager as administrator and set the port to the one in the Windows Device Manager (Shown in picture above).
 +You may need to check the Keyboard Wedge checkbox as well.
 Once this is done, no other configurations are necessary.  Once this is done, no other configurations are necessary. 
 In this configuration, the STX Prefix is not needed. System Five and the POS Device Manager will be monitoring that port for activity. In this configuration, the STX Prefix is not needed. System Five and the POS Device Manager will be monitoring that port for activity.
 +
 +
 +
 +
 +====== Removing Leading And Trailing Digits From UPC Barcodes ======
 +
 +<note important> Removing digits from the UPC barcodes is not recommended. However, in some very specific cases this could be done.
 +Be aware that if you do this, it will do it for all barcodes going forward, and all barcodes scanned previously with the first and last digits attached will not scan anymore.
 +So you MUST be absolutely sure that you need to do this. </note> 
 +
 +Print the following document and scan the highlighted 2D barcodes in the numerical order specified. 
 +
 +{{ :barcodescan:820055914_tom.pdf |}}
  
  
datalogic_quickscan_2d.txt · Last modified: 2021/12/06 15:57 (2 years ago) by swind